The article author is making several great annotation on A Step-by-Step Guide to Installing a Bathtub as a whole in this content which follows.
Setting up a tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and sometimes, tiling skills. Changing an old tub with a new one is additionally a reasonably tough job. If the old bathtub is conveniently easily accessible, the job can relocate rapidly; if you have to open up a wall to get rid of the old tub and position the brand-new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. Make certain you have certified yourself for the job and also fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is much better to think about utilizing one before you start. Possibilities are you may need an expert plumber to make tube links.
This article will aid you mount a new bathtub in your bathroom if you have already gotten a brand-new bathtub as well as do not need to transform the arrangement of your previous supply of water pipes.
Your devices as well as product checklist must make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be fairly troublesome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Utilizing both wood boards under its feet, put the bath tub in the required placement. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reviews degree.
To install taps, fit the bottom of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the various other tap.
Turn on the water supply and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bath tub and additionally examine the overflow outlet and the normal electrical outlet for leakages.
Finally, repair the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the tub should wait until the bathtub has actually been made use of at least once as this will settle it right into its last placement.
Planning for the Installment
To start with, the sustaining framework provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, creating the water to pass through the wall in between the bath and the tiling, resulting in problems with dampness and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealer can break rather very early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub Yourself, I was thinking sharing that excerpt was smart. Are you aware of another individual who is interested by the subject? Take a moment to promote it. Many thanks for taking the time to read it.
Drips? Dial fast!